Struct tokio::net::unix::ReadHalf

pub struct ReadHalf<'a>(/* private fields */);

Borrowed read half of a UnixStream, created by split.

Reading from a ReadHalf is usually done using the convenience methods found on the AsyncReadExt trait.

Implementations

impl ReadHalf<'_>

pub async fn ready(&self, interest: Interest) -> Result<Ready>

Wait for any of the requested ready states.

This function is usually paired with try_read(). It can be used instead of readable() to check the returned ready set for Ready::READABLE and Ready::READ_CLOSED events.

The function may complete without the socket being ready. This is a false-positive and attempting an operation will return with io::ErrorKind::WouldBlock. The function can also return with an empty Ready set, so you should always check the returned value and possibly wait again if the requested states are not set.

This function is equivalent to UnixStream::ready.

Cancel safety

This method is cancel safe. Once a readiness event occurs, the method will continue to return immediately until the readiness event is consumed by an attempt to read or write that fails with WouldBlock or Poll::Pending.

pub async fn readable(&self) -> Result<()>

Waits for the socket to become readable.

This function is equivalent to ready(Interest::READABLE) and is usually paired with try_read().

Cancel safety

This method is cancel safe. Once a readiness event occurs, the method will continue to return immediately until the readiness event is consumed by an attempt to read that fails with WouldBlock or Poll::Pending.

pub fn try_read(&self, buf: &mut [u8]) -> Result<usize>

Tries to read data from the stream into the provided buffer, returning how many bytes were read.

Receives any pending data from the socket but does not wait for new data to arrive. On success, returns the number of bytes read. Because try_read() is non-blocking, the buffer does not have to be stored by the async task and can exist entirely on the stack.

Usually, readable() or ready() is used with this function.

Return

If data is successfully read, Ok(n) is returned, where n is the number of bytes read. If n is 0, then it can indicate one of two scenarios:

1. The stream’s read half is closed and will no longer yield data.
2. The specified buffer was 0 bytes in length.

If the stream is not ready to read data, Err(io::ErrorKind::WouldBlock) is returned.

pub fn try_read_buf<B: BufMut>(&self, buf: &mut B) -> Result<usize>

Tries to read data from the stream into the provided buffer, advancing the buffer’s internal cursor, returning how many bytes were read.

Receives any pending data from the socket but does not wait for new data to arrive. On success, returns the number of bytes read. Because try_read_buf() is non-blocking, the buffer does not have to be stored by the async task and can exist entirely on the stack.

Usually, readable() or ready() is used with this function.

Return

If data is successfully read, Ok(n) is returned, where n is the number of bytes read. Ok(0) indicates the stream’s read half is closed and will no longer yield data. If the stream is not ready to read data

pub fn try_read_vectored(&self, bufs: &mut [IoSliceMut<'_>]) -> Result<usize>

Tries to read data from the stream into the provided buffers, returning how many bytes were read.

Data is copied to fill each buffer in order, with the final buffer written to possibly being only partially filled. This method behaves equivalently to a single call to try_read() with concatenated buffers.

Receives any pending data from the socket but does not wait for new data to arrive. On success, returns the number of bytes read. Because try_read_vectored() is non-blocking, the buffer does not have to be stored by the async task and can exist entirely on the stack.

Usually, readable() or ready() is used with this function.

Return

If data is successfully read, Ok(n) is returned, where n is the number of bytes read. Ok(0) indicates the stream’s read half is closed and will no longer yield data. If the stream is not ready to read data Err(io::ErrorKind::WouldBlock) is returned.

pub fn peer_addr(&self) -> Result<SocketAddr>

Returns the socket address of the remote half of this connection.

pub fn local_addr(&self) -> Result<SocketAddr>

Returns the socket address of the local half of this connection.

Trait Implementations

impl AsRef<UnixStream> for ReadHalf<'_>

fn as_ref(&self) -> &UnixStream

Converts this type into a shared reference of the (usually inferred) input type.

impl AsyncRead for ReadHalf<'_>

fn poll_read( self: Pin<&mut Self>, cx: &mut Context<'_>, buf: &mut ReadBuf<'_> ) -> Poll<Result<()>>

Attempts to read from the AsyncRead into buf.

impl<'a> Debug for ReadHalf<'a>

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.